Vevor

Made of heavy steel with a good coat of paint. The drawer compartment dividers are steel and are sealed at the bottom of the drawer so the smaller drill bits can't go underneath. I am very pleased with this drawer set. Well worth the money.

Orderd a dolly converter several weeks ago.It worked perfectly once I made my own dolly with 2x6 boards. The dollys you can buy pre-made are too thin and not wide enough to make the rails sturdy. I do recommend this if you can use 2x6 boards.

Needed a 50A cable to connect my generator to my house but I needed it to have just one male plug on it. They had a great choice and I was able to buy one cable with a male plug on one end and bare wires on the other.

Got it within' a couple days and worked great for my application once I installed my second male plug.

WARNING! Dont go near this company! I bought a plasma cutter and when connected to 220V the casing is live and i got an electrical shot from the machine when i touched it.

When asking for replacement or refund i was offered 20 euro and keep it. I declined of course. After a few days im offered 40 euro and keep it!? Again i declined and i asked if they are joking? A few days more and i am offered 60 euro?

Support is a complete disaster and now i am stuck with a machine that is lethal if i connect it to the socket.
Amazing that a company like this can still exist in 2023!

It's a great hammer to do most demolition jobs. I've used it a few times and it delivered impressive performance each time. It is heavy, but I guess it needs to be heavy to do the jobs it is meant to do

This thing sucks! It's meant to! I had to replace a memory chip on my Atari 130XE. I've never used a tool like this before, but it worked well, and didn't harm the pads at all. I set it to 350C, and it melted the solder each time, and sucked it all up. I had to use very minimal force to pull the chip out after it cooled down. Well worth the price for home & professional repair!

Purchased a Vevor pond vacuum and barrel locks do not hold barrel lid on at all! They are riveted in the wrong place so the vacuum is useless! I give it a 0 out of 5. All we get from China is we don't understand your problem! We lost $189.00 don't buy anything from Vevor they are a complete ripoff!
Stephen & Laura

It arrived late and the instructions leave much to be desired but this is a great motorcycle tent. I staked it to the ground and put a 4x8 sheet of plywood down for a floor. Plenty of room for Vulcan 900 Classic!

It's good, just fill the bottle with cutting sulution, set on your work do all your lining up then turn on magnetic switch, now with drill off move handle down check your specks, ready turn on dilution and then the drill juice on bit lite touch and easy set there and note it hole no hard pressure just easy and with the juice on the bore bit, this a must no juice no bore, and lite pressure, it's not a fast operation, it's not intended to be, but the results are the nicest, I've used $6000. 00 drills and bore bits that the finish is no better than with this tool, note find you a plate bolt it to your work bench no clamps set your mag drill and u can drill plate to a degree on your work bench, good luck, and take ur time

I use distilled water for my BiPAP and was tired of having to buy distilled water. This distiller works great. I used it to distill wine also. Shipping was fairly quick. All materials are food safe. I would gladly recommend this to my friends.

We ordered a machine, it failed after one day of use. I have attempted to get an RMA for almost a month to use (Hassel-Free 30 day returns) but now am told they need pictures and video of the failure. The machine is already packed and ready for shipment. We have already purchased a superior, American-made machine and only wish to get a refund according to their website.

MAKE SURE TO READ vevor.com reviews on site jabber! vevor.ca and vevor.com are the same people!

I have been wanting another one of these slicers for a long time and this one is great. It looks like my last one and has the same features. I like it a lot and and will enjoy using it. I'm happy with them.

I purchased on-line, after a YouTube recommendation, a 2017 Honda CRV roof rack system. I have had issues with the left rail whereby I am unable to properly secure the back cross rail due to a defect. Also one of the 8 covers is defective. I am left to "MacGiver" a new product. I am going on week three of back and forth communications with customer service and still no resolution. It isn't like I can send it back because I have cut the trim on my CRV and can not reinstall it. It's like the department that is sent the defect information doesn't read the case notes. So frustrating! (see picture - one of the silver "grommets" just spins and will not allow the screw provided to tighten the rack onto the rail. I had to use needle nose pliers to get the cross bar off (hence the scratches). The other minor issue was one of the covers (seen in this picture) had a stcky pad missing, so the cover doesn't sit level on the rail.

I'm really happy.For the money this router is the best deal you're gonna get. You can always do upgrades afterwards. It's a lot better than a 3018 cnc router. For me Mach3 software is a lot better than grbl. You can't use height offset or tool compensation and can't use drilling cycle in grbl.

Bought a 4 inch one after struggle with a smaller vise. Wasn't expecting it to be as good as it turned out to be at a tiny fraction of the price. Was well packed, came with a fixing kit, and was no trouble to setup. After fly cutting a part both sides on parallels the thickness was almost same on all corners (just over 0.01mm). Extremely good clamping force.

Bought this grill last week was shipped quickly. I took it out the box soon has I got it and stated using it right away Great grill glad I ordered it you won't go wrong with it wife loves it Thanks Vevor

I recently bought a water distiller from Vevor which got delivered so fast that I couldn't believe it. The distiller works fine, and I am satisfied with this product. Would I order from Vevor again? You bet!

I bought a honey extractor from them that upon testing it was too small for the hight of the frames, they would hit the top when you were spinning them it has only1 mm of clearance which is not enough. I called them to see what they wanted to do about it, they wanted to see a video, so I send them one showing the problem. I was told by a Vevor representative that she would ask the product sender to send me a return label but he asked me for measurements of the frames the frames are standard size frames, we went back and forth about the extractor not having enough clearance, well it seems like I am not going to get my return label and be stuck with a useless extractor and out a couple of hundred of dollars, so please be aware when buying from Vevor, from what I see they supply cheap product and they don't back them up. So never again for me and I would suggest you as well unless you find yourself in the same predicament.

I bought a diesel heater.Seems very powerful! Easy to use. Too much smoke just on the first start. I thought that it would be more noisy but it is not.